I fixed my smartphone’s charging port, broken rear glass, and dying battery for under R800 & More Trending News

I repaired my Xiaomi Mi 9T Pro’s charging port, broken rear glass, and dying battery for R780.24 — and it’s now like new.

The Xiaomi Mi 9T Pro, also referred to as a Redmi K20 Pro, was sitting in my drawer after I upgraded to a Samsung S22+.

The Xiaomi was nonetheless in working order, however I dropped it just a few instances, which brought on the rear glass to interrupt.

It had just a few sharp edges, however it helped to stay it in a silicone case.

The cellphone’s battery was additionally deteriorating. Accubattery indicated an precise capability of two,923 mAh, considerably decrease than the unique 4,000 mAh.

To make issues worse, it was a wrestle to cost the cellphone. The USB C port was worn out to the purpose the place solely particular cables held on the proper angles would work.

The cellphone has excellent specs for a tool launched in 2019, with a Snapdragon 855 and 6 GB of RAM.

The machine additionally sports activities a 48MP digital camera that takes nice photos, has a twin SIM, and helps LTE-A.

Even with these nice specs, the charging port made it disagreeable to make use of.

I regarded into replacements for the broken components and discovered a brand new glass again panel and the circuit with the USB port on it for R381.

It regarded like an excellent deal to restore a high-end smartphone and reserve it from turning into e-waste.

While ready for the brand new parts, we discovered a brand new battery on Aliexpress for R366.29 after delivery.

I purchased the parts with cryptocurrency, and the glass again panel and the circuit arrived two weeks later.

However, the battery took virtually three months, and it needed to be collected from a Post Office for an extra R32.95 price.

The battery included useful instruments to open the again of the machine, together with a suction cup, two prying instruments, two picks, and two small screwdrivers.

It was time to repair the Xiaomi Mi 9T Pro.

I began by eradicating the previous rear glass, which was fairly straightforward because it was broken already.

Pulling with the suction cup whereas working our method by the glue with a decide had it off very quickly, revealing the insides.

If the rear panel have been nonetheless in good situation, a warmth gun would have helped soften the glue throughout this step.

With holes within the cellphone’s rear, a number of grime had made its method inside. I cleaned it utilizing alcohol pads to forestall it from getting in any connectors we needed to take away.

I was prepared to begin dismantling the within.

I first eliminated the screws holding the protecting plates over the electronics.

Watching a video the place another person disassembles the identical machine helped to level out easy-to-miss screws and the order of eradicating components.

After eradicating the plates, we might disconnect the battery connector and different connectors on the underside board that we wished to exchange.

These connectors are simply lifted utilizing one of many prying instruments. However, you need to be very cautious to not break a whole plug off the boards.

The previous battery was trivially eliminated utilizing the pull tabs. We might slot the brand new one in utilizing the identical adhesive that remained hooked up to the remainder of the cellphone.

The alternative backside board was not similar to the unique. It appeared to overlook further floor connectors, however we went forward with the swap anyway.

The remainder of the parts went in the identical method we eliminated them, with all of the plugs clicking into place with minimal power.

We checked the machine labored earlier than closing it again up, and it powered on instantly with the battery round 40%.

The new charging port additionally labored completely, together with Quick Charge.

Before glueing on the brand new rear panel, we went across the again of the machine once more with an alcohol wipe to ensure all of the glue surfaces have been clear.

It helped to make sure the panel would stick correctly.

The again panel was rigorously positioned and pressed down throughout the skin of the machine the place the pre-applied glue was positioned.

The machine now capabilities as a brand new cellphone. Only the damage and tear on the steel body makes it apparent this Mi 9T Pro is secondhand.

Accubattery estimates an precise battery capability of 3479 mAh. It isn’t good, however it ought to give the machine some further life.

I carried out just a few charging cycles and did stress exams whereas monitoring for any issues.

Seven hours of screen-on time solely diminished the battery to 40% from a full cost.

This cellphone is now prepared for use once more, charging simply, offering good battery life, and not hurting the consumer due to a cracked again cowl.

---

Now learn: I constructed an ambient backlight system for my laptop display for R600

I have tried to offer all types of stories to all of you latest news today 2022 by this web site and you will like all this information very a lot as a result of all of the information we all the time give on this information is all the time there. It is on trending matter and regardless of the newest information was

it was all the time our effort to achieve you that you simply maintain getting the newest information and you all the time maintain getting the data of stories by us for free and additionally inform you individuals. Give that no matter data associated to different forms of information will likely be

made obtainable to all of you so that you’re all the time related with the information, keep forward within the matter and maintain getting today news all forms of information for free until immediately as a way to get the information by getting it. Always take two steps ahead